![]() ![]() Tls-auth /var/etc/openvpn/server1.tls-auth 0 Management /var/etc/openvpn/server1.sock unix If you use/want NetBIOS and/or WINS server(s) to be available to the VPN'd devices, set the applicable valuesĬlient-connect /usr/local/sbin/Ĭlient-disconnect /usr/local/sbin/Īuth-user-pass-verify /var/etc/openvpn/server1.php via-env The wizard will have filled in the NTP Server's address that's set in pfSense – while it's probably a good idea to leave it for future use, currently the iOS OpenVPN Connect client/app won't use it ![]() This is of critical importance if you want the VPN'd devices to be able to resolve LAN-based/non-public names via an internal-only DNS server Normally, the DNS Server entry(s) should be the same as the DNS servers configured for systems that reside on the network set in "Local Network" The DNS Default Domain entry should be the domain name for the network set in "Local Network" This will allow the VPN connection to be maintained as a mobile device receives another IP address from the network to which it's attached (e.g., it's DHCP lease expired and it was allocated another address) When you use multiple user accounts but want to use the same certificate for all or collections of devices When you use the same user account and user certificate across multiple devices (e.g., one user account per group or just one for everyone in a small organization or home scenario) If you want to use one user certificate across multiple mobile devices, then ensure that Duplicate Connections is checked – e.g., this would be required: If you want the VPN-connected mobile devices to be able to create network connections with each other, then ensure that Inter-Client Communication is checked, otherwise ensure it's unchecked If you want only the connected mobile device's networking traffic to/from your site to flow through the VPN tunnel, ensure that Redirect Gateway is uncheckedįor Local Network, enter the Network IP address and the applicable CIDR routing prefix/mask for the LAN to which the VPN'd mobile device is to have accessĮnter the maximum number of Concurrent Connections you want to be supported – this must be consistent with the number available via the "Tunnel Network" setting, above This is "safer" but may also noticably slow the mobile device's data communications (depending upon your network's speed, traffic shaping and latency charateristics) If you want all the connected mobile device's networking traffic to be routed through your network via the VPN tunnel (i.e., so any unencrypted traffic only emanates from your network/firewall), ensure that Redirect Gateway is checked This will determine the maximum number of concurrent mobile client connections that can be allocatedĮ.g., 172.24.48.0/29 will cause 172.24.48.1 to be allocated as the mobile OpenVPN gateway IP address and connected mobile clients to be assigned a "virtual" IP in the range of 172.24.48.2 thru 172.24.48.7 This will be the "virtual"/remote network from which the VPN'd mobile device will appear (i.e., be routed) in pfSense In the majority of cases, this will be your WAN interface – i.e., mobile users will connect to your pfSense router directly from the Internetįor Local Port enter 1194, the normal port for OpenVPN communicationsĮnter a Description for this OpenVPN serverĮnsure that TLS Authentication is checkedįor Tunnel Network, enter a Network IP address and the applicable CIDR routing prefix/mask Select the Interface that will receive the OpenVPN connections Option A" on the a.4) IPSec VPN Server Setup (with certs) page, select that server certificate ("GoDaddy Server Certificate" in that example) If you're using a server certificate that you loaded into pfSense in step "1. Option B" on the a.4) IPSec VPN Server Setup (with certs) page (" server certificate" in that example, which is what we'll use in this example) If you're using pfSense-generated "self-signed" certificates, select the server certificate you generated in step "1. Option A" on the a.4) IPSec VPN Server Setup (with certs) page, select that certificate authority ("goDaddy certificate authority" in that example) If you're using pfSense-generated "self-signed" certificates, select pfSense Internal Certificate Authority (we'll use this in our example) In pfSense, visit the VPN → OpenVPN → Wizards tab – which will start the "OpenVPN Remote Access Server Setup Wizard"įor Type of Server, select Local User Access (this is really selecting the source for the user accounts) ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |